Analysis Of Hand Tractor Performance Using Moldboard Plow Based On Different Plowing Patterns

Authors

  • Dwi Santoso
  • Muhammad Fiqih Faculty of Agriculture, Borneo Tarakan University
  • Sudirman Sirait Faculty of Agriculture, Borneo Tarakan University
  • Abdul Waris 2Department of Agriculture Engineering, Hasanuddin University
  • Deny Murdianto Faculty of Agriculture, Borneo Tarakan University
  • Ince Siti Wardatullatifah Faculty of Food Technology and Agroindustry, Mataram University
  • Anugerah Fitri Amalia National Research and Innovation Agency
  • Kusmali Kusmali Department of Biosystem Engineering, Sumatera Institute of Technology
  • Saat Egra Faculty of Agriculture, Borneo Tarakan University
  • Siti Fatima Agrotechnology Study Program, Sekolah Tinggi Ilmu Pertanian Mujahidin Tolitoli

DOI:

https://doi.org/10.35334/iciksa.v0i0.54

Abstract

Inappropriate selection of plow patterns can cause a lot of time lost due to the many turns during tillage. Plowing patterns are chosen with the aim of minimizing as much as possible the lift of the implement to reduce turn time, the more lifting of the tool when turning, the lower the efficiency. And it takes a lot of time, effort and money. This study aims to determine the performance of hand tractors in different plowing patterns. the stages of this research are problem identification, identification of plotting patterns, performance testing and data analysis. Plowing patterns used are edge patterns, middle patterns and spiral patterns. The research parameters used are wheel slip, actual working capacity, theoretical work capacity and work efficiency. The results show that the edge pattern is the best pattern with the highest working capacity value of 87% and the lowest wheel slip of 12% and the highest work efficiency of 92%.

References

Catur, Cahyawan, Edi Margana, Sirajuddin Haji Abdullah. 2014. Studi Kinerja Lapang Berbagai Traktor Tangan Pada Budidaya Kacang Tanah ( Arachis Hypogeae L ). Jurnal Ilmiah

Rekayasa Pertanian dan Biosistem 2 (2): 64–72.

Coffman. B.A. et all. 2010. Testing Fuel Efficiency Of A Tractor With A Continuously Variable Transmission. Biological system Engineering. 26 (1)

Handayani, T R I. 2017. Efisiensi Penggunaan Bahan Bakar Pada Traktor Roda Dua Terhadap Pengolahan Tanah. Jurnal Hijau Cendekia 2: 83–86. [4] Mardinata, Z., & Zulkifli, Z. 2014. Analisis Kapasitas Kerja dan Kebutuhan Bahan Bakar Traktor Tangan Berdasarkan Variasi Pola Pengolahan Tanah, Kedalaman Pembajakan dan Kecepatan Kerja. agriTECH, 34(3), 354-358

Margana, C. C. E., & Putra, G. M. D. 2017. Performansi Traktor Tangan Roda Dua Modifikasi Menjadi Roda Empat Multifungsi (Pengolahan Dan Penyiangan) Untuk Kacang Tanah Di Kabupaten Lombok Barat. Jurnal Ilmiah Rekayasa Pertanian dan Biosistem, 5(1), 296-302. [6] Marlia, Y., Hersyamsi, H., & Triana, A. N. 2017. Uji Kinerja Bajak Singkal Yang Dilapisi Lembaran Tembaga Pada Pengolahan Tanah Ultisol Skripsi (Doctoral dissertation, Sriwijaya University).[7] Kementan. (2019). Statistik Sarana Pertanian Tahun 2018 Statistics Of Agricultural Facilities.

Santoso, D. & Rahajeng, G.Y & Wijaya, R. 2020. Identifikasi Kebutuhan Alsintan Tanaman Pangan (Padi Dan Jagung) Di Kota Tarakan. Jurnal Ilmiah Inovasi. 20 (3)

Santoso, D. & Murdianto D. 2022. Artificial Intelligence in the Perspectives of Agricultural Technology Development in Indonesia. Budapest International Research and Critics Institute (BIRCI-Journal): Humanities and Social Sciences. 5 (1)

Downloads

Published

2022-09-28

Issue

2022

Section

Articles